Components

12v Connection set for (air) horns and klaxons. All necessary components for the installation of our 12v horns. Includes the necessary wiring, switch, connectors and fuse.

Hadley Snow Cap, or Shield. 195mm diameter. Suitable for Hadley air horns type H00868. Polished Stainles Steel.

Hadley matte black snow cover, or shield. H00928BLCK, 195mm diameter. Suitable for the matte black Hadley horns H00894BCE or the chrome H00868ECE.

Hadley Snow Cap, or Shield. 175mm diameter. Suitable for Hadley air horns type H00861 and E-tones H09318AC, H09321AC, H09324AC. Polished Stainless Steel.

Hadley matte black snow shield H00929BLCK, 175mm diameter. Suitable for Hadley horns H00861ECE with a length of 62 cm.

Hadley Snow Cap, or Shield. 148mm diameter. Suitable for Hadley air horns type H00885 and H00886. Polished Stainless Steel.

Hadley matte black snow shield H00927BLCK, 148mm diameter. Suitable for Hadley horns H00885ECE end 886ECE with a length of 48- and 56 cm.

FIAMM Set of 2 Shields for TA150 and TA180 truck air horns.

Hadley Snow Cap, or Shield. 105mm diameter. Suitable for Hadley air horns type "Bully". Polished Stainless Steel.

Electronic valve with solenoid coil, normally closed, 6mm in- and output, suitable for both 12v and 24v. up to 12 bar pressure

Valve with electro-mechanical solenoid, normally-closed, broad input side, brass, 12V, operates from 0bar up to 16bar pressure, input & output has 1/8" BSP thread, for truckhorns.

Luchthoornventiel met ruime doorgang. 24v ventiel voor o.a. bediening van truckhoorns. Werkt van 0 tot 16 bar. In- en uitgang 1/8 BSP (draad). Met- of zonder slangkoppelingen leverbaar.

Pull valve with cord. Valve with connection for 6mm tube. Supplied with cord and compression fittings for 6mm tube. Male thread on couplings is 1/8 BSPP (gas).

Lanyard valve Large, normally-closed,, operates from 0bar up to 10bar pressure, input & output has 1/4" BSP thread.

Hadley Code: H00550A

Hadley electronic valve for mounting on air horn with 1/4 NPT thread. The H00550C is especially for air horns with a 1/4 NPT (threaded) entry.

Kogelkraan of afsluiter met 1/2 BSP draad bij in- en uitgang. Kan als afsluiter voor pneumatisch systeem worden gebruikt, maar ook als handmatig ventiel.

Kogelkraan of afsluiter met 1/2 BSP draad bij in- en uitgang. Kan als afsluiter voor pneumatisch systeem worden gebruikt, maar ook als handmatig ventiel.

Kogelkraan of afsluiter met 3/8 BSP draad bij in- en uitgang. Kan als afsluiter voor pneumatisch systeem worden gebruikt, maar ook als handmatig ventiel.

Kogelkraan of afsluiter met 1/2 BSP draad bij in- en uitgang. Kan als afsluiter voor pneumatisch systeem worden gebruikt, maar ook als handmatig ventiel.

Fiamm Air horn Support for the types TA 180 and TA150.

Hadley Medium Size Horn support

Hadley Item: H00860-6

Hadley Diaphragm kit for Hadley Airhorns.

Fiamm electric solenoid valve for vehicles with 12v electrical system. This solenoid valve comes with 1/8 threaded inlet and outlet. For both ends tighten fittings for 6mm air tube are included.

Hadley code: H1311020S

Relay, 4-pin, 12V for the electrical connection of (air) horns. Usually included with most of our 12V air horn kits with a compressor and electromagnetic horns.

Hadley Air Tank. Losse luchttank van Hadley met 4,5 liter inhoud (275 cubic inch) Afmeting 12,7 x 35,5 cm. Deze luchtank wordt geleverd met 1/4 (Amerikaanse maat) fittings.

Pressure switch for compressor sets. Switching on at 90psi (6 bar). Shuts off at 120psi (8 bar). Supplied as standard on VIAIR set 20003.

Hadley Pressure Switch H13940S.

Hadley Air Gauge (max. 160 PSI)

Fiamm TA/O single air horn with high tone. Works with compressed air from 1-2 bar. (Compressor not included)

Set of two air horns manufactured by Fiamm. The red plastic horns have a high and a low tone. Hose, divider and mounting nuts are included. (please note: you will need an airsource)

Special service set for Hadley Bully horns. The set contains among other things two membranes (Ø 62 mm) to exchange for a better sound of your Bully horns.

Hadley code: H00977HB

FIAMM connection cable for siren modules

Hadley seal for Hadley horns with empty PTC inlet. Complete set to connect 6 mm tube directly to Hadley horns with inlet without thread, or plug-in coupling. (NOTE: Only empty PTC)

Throttle valve 6mm PTC 1/8 BSP. Throttle valve, or also flow reducer. This valve can reduce the amount of air.

Throttle valve 8mm PTC 1/8 BSP. Throttle valve, or also flow reducer. This valve can reduce the amount of air.

Throttle valve 8mm PTC 1/4 BSP. Throttle valve, or also flow reducer. This valve can reduce the amount of air.

Separate 12v FIAMM Siren compressor. Suitable for, among others, Italian Fire Brigade and Ambulances. Successor of FIAMM MC2/FVA

Spiral tube Ø8mm including couplings (1/4 bsp male) with spring. When extended 6 meters long.

Luchthoornsteun voor de voorzijde van de Burtone scheepshoorns. Ontwikkeld voor de twee grotere types; de H320 en H330.

Relay, 4-pin, 24V for the electrical connection of (air) horns. Usually included with most of our 24V air horn kits with a compressor and electromagnetic horns.

Air filter for pneumatic systems. A valve can become clogged by debris from the air tank or compressor, which may cause it to block or seize. Connecting this filter to the valve inlet can prevent this

FIAMM siren amplifier especially for cycling race follow-up vehicles.

Two-pole toggle switch with on-off function. Suitable for 12 V DC and 25 amperes.

Sticker with Hadley logo, specially for Hadley Truck Horns H00977ECE and H00978ECE

FIAMM JPT Jumper Connector. This jumper allows two AM80SX horns (high and low) to be connected simultaneously.